Resin transfer molding process: a numerical and experimental investigation
DOI:
https://doi.org/10.1260/1750-9548.7.2.125Abstract
Resin Transfer Molding (RTM) is one of the composite manufacturing technique that consists in injecting a resin pre-catalysed thermosetting in a closed mold containing a dry fiber preform, where the resin is impregnated. In this sense, the aim of this research is to study theoretically and experimentally the RTM process. Experimental and simulations of the rectilinear infiltration of polyester resin (filled and non filled with CaCO3) in mold with glass fiber preform were performed in cavity with dimensions 320 x 150 x 3.6 mm. Numerical results of the filling time and fluid front position over time were assessed by comparison with experimental data and good accuracy was obtained. It was verified that, the CaCO3 content affect resin velocity during filling, the permeability of the reinforcement and resin viscosity, thus the filling time is affected strongly.
References
C. D. Rudd, A. C. Long, K. N. Kendall, and C. Mangin, Liquid moulding technologies, 1a ed., Woodhead Publishing Limited, Cambridge England, 1997.
D. A. Steenkamer, The influence of preform design and manufacturing issues on the processing and performance of resin transfer molded composites. Publishing House University of Delaware, 1994.
K. T. Hsiao, Simulation-based liquid injection control (SLIC): Methodology and applications in RTM and VARTM. University of Delaware, Center for Composite Materials, 2003.
D. Lefevre, S. Comos-Cardona Binétruy, and P. Krowczak, Modelling the flow of particle-filled resin through a fibrous perform in liquid composite molding technologies, Applied Science Manufacturing, 2007, Vol. 38 (10), 2154-2163. https://doi.org/10.1016/j.compositesa.2007.06.008
W. F. Amorim Júnior, G. Q. Chaves, V. M. A. Calado, and F. L. Bastian, Processing thick composite board by resin transfer molding. Revista Matéria, 2006, Vol. 11 (3), 316-323.
R. Gerlach, C. R. Sivion, N. Petrinic, and J. Wiegand, Experimental characterisation and constitutive modelling of RTM-6 resin under impact loading. Polymer, 2008, Vol. 49 (11), 2728-2737. https://doi.org/10.1016/j.polymer.2008.04.018
M. Haider, P. Hubert, and L. Lessard, An experimental investigation of class a surface finish of composites made by the resin transfer molding process. Composites Science and Technology, 2007, Vol. 67 (15-16), 3176-3186. https://doi.org/10.1016/j.compscitech.2007.04.010
B. Gourichon, C. Binetruy and, P. Krawczak, Experimental investigation of high fiber tow count fabric unsaturation during RTM. Composites Science and Technology, 2007, Vol. 66 (7-8), 976-982. https://doi.org/10.1016/j.compscitech.2005.07.032
Y. Kuan and, A. S. ElGizawy, Numerical Characterization of mold injection in resin transfer molding process, Advances in Polymer Technology, 2000, Vol. 19 (3), 173-179. https://doi.org/10.1002/1098-2329(200023)19:3<173::aid-adv2>3.0.co;2-c
M. Hattabi, J. Echaabi and, O. Bensalah, Numerical and experimental analysis of the resin transfer molding process, Korea & Australia Rheology Journal, 2008, Vol. 20 (1), 7-14.
G. L. P. Machado, A. C. Garay, P. B. Roese, T. M. Schmidt, J. A. Souza, and S. C. Amico, Numerical Simulation of Infiltration in Manufacturing Process for Composite RTM. X CBpol-Brazilian Congress of Polymers, 2009.
F. Sánchez, J. A. García, L. Gascón and, F. Chinesta, Towards an efficient numerical treatment of the transport problems in the resin transfer molding simulation. Computer Methods in Applied Mechanics and Engineering. 2007, Vol. 196 (21-24), 2300-2312. https://doi.org/10.1016/j.cma.2006.07.018
F. F. Luz, S. C. Amico, J. A. Souza, E. S. Barbosa, and A. G. B. Lima, Numerical Analysis of Heat and Mass Transfer in Porous Media, edited by J. M. P. Q. Delgado, Antonio Gilson Barbosa de Lima and Marta Vázquez da Silva, Springer, Heidelberg (2012). https://doi.org/10.1007/978-3-642-30532-0_5
J. A. Destephen, and K. J. Choi, Modeling of filtration processes of fibrous filter media. Separations Technology. 1996, Vol. 6 (1), 55-67. https://doi.org/10.1016/0956-9618(96)00140-3
A. C. Garay, V. Heck, A. J. Zattera, J. A. Souza, and S. C. Amico, Influence of calcium carbonate on RTM and RTM light processing and properties of molded composites. Journal of Reinforced Plastics Composites, 2011, Vol. 30 (7), 1213-1221. https://doi.org/10.1177/0731684411416033
PAM-RTM - User's Guide & Tutorials, 2009.
Published
How to Cite
Issue
Section
Copyright (c) 2013 I Oliveira, S Amico, J Souza, A Lima
This work is licensed under a Creative Commons Attribution 4.0 International License.